Key Features64-bit MIPS-based processor operating at 700 MHz45-Gbps switch fabric and 1.2-Gbps cell-bus (when used with chassis other than the Cisco MGX 8950)Cisco PXM-45/C used only as processor in Cisco MGX 8950; Cisco MGX-XM-60 provides switch-fabric function in that chassisHot swappable1:1 hot-standby redundancyUser-selectable primary and secondary clock sources with graceful switchoverInternal Stratum-3, external Building Integrated Timing Supply (BITS), or in-band clock sourcesIn-band or out-of-band management using EIA/TIA-232 or 10BASE-T control portsSupport for narrowband and broadband service modules scaling from DS-0 to OC-48c/STM-16 or DS-3/E3 to OC-192/STM-64 (depending on the chassis used)Chassis compatibilityCisco MGX 8830/B, MGX 8850, MGX 8850/B, MGX 8880, and MGX 8950Software compatibilityMinimum Cisco MGX software release supporting Cisco PXM-45/C:Cisco MGX 8850 Software Release 4.0.15Cisco MGX 8950 Software Release 4.0.15 Cisco MGX Software Release 5.0.20 (for Cisco MGX 8880 and MGX 8850/B)Cisco MGX Software Release 5.2.00 (for Cisco MGX 8830/B)Network Management Managed by Cisco WAN Manager Software suite Based on Simple Network Management Protocol (SNMP)PowerInput power required: -48 VDCPower consumption: 128 WPhysical DimensionsH x D: 15.75 x 16.5 in. (40.00 x 41.91 cm)Weight6.5 lbs

Key FeaturesThe main features of the Cisco 8-Port OC-12/STM-4 Channelized/Unchannelized ATM Switch Service Module are listed here.Full nonblocking, full-duplex line-rate throughput on all 8 ports when used on the Cisco MGX 8950 chassisUp to 4 ports with nonblocking, full-duplex line-rate throughput when used on the Cisco MGX 8800 chassisIndividual port channelization down to DS-3 and OC-3c/STM-1Per-virtual-path and per-virtual-circuit traffic shaping and available bit rate (ABR) with virtual source and virtual destinationAPS (1:1 and 1+1) port redundancy, plus APS 1+1 card redundancyUp to 4 million cell buffersUp to 16 classes of service (CoS) that can be used to support IP or ATM servicesSupport for standards-based Private Network-to-Network Interface (PNNI), switched virtual circuit (SVC) and switched virtual path (SVP), soft permanent virtual connection (SPVC) and soft permanent virtual path (SPVP), and Multiprotocol Label Switching (MPLS) servicesChassis CompatibilityCisco MGX 8830/B, MGX 8850, MGX 8850/B, MGX 8880, and MGX 8950Software CompatibilityCisco MGX 8800/8900 Software Release 5.2.00 and above for Cisco MGX 8830/B, MGX 8850, MGX 8850/B, and MGX 8950Cisco MGX 8800/8900 Software Release 5.3.00 and above for Cisco MGX 8880ProtocolsATM and SONET/SDHPort Density8 ports (4 ports at full line rate on the Cisco MGX 8800 chassis)Network ManagementManaged by Cisco WAN Manager software suiteBased on Simple Network Management Protocol (SNMP)PowerInput power required: -48 VDC Power consumption: 134WPhysical DimensionsH x D: 15.83 x 15.65 in. (40.20 x 39.75 cm)Weight6.5 lb (2.95 kg)

Key FeaturesThe main features of the Cisco 8-Port OC-12/STM-4 Channelized/Unchannelized ATM Switch Service Module are listed here.Full nonblocking, full-duplex line-rate throughput on all 8 ports when used on the Cisco MGX 8950 chassisUp to 4 ports with nonblocking, full-duplex line-rate throughput when used on the Cisco MGX 8800 chassisIndividual port channelization down to DS-3 and OC-3c/STM-1Per-virtual-path and per-virtual-circuit traffic shaping and available bit rate (ABR) with virtual source and virtual destinationAPS (1:1 and 1+1) port redundancy, plus APS 1+1 card redundancyUp to 4 million cell buffersUp to 16 classes of service (CoS) that can be used to support IP or ATM servicesSupport for standards-based Private Network-to-Network Interface (PNNI), switched virtual circuit (SVC) and switched virtual path (SVP), soft permanent virtual connection (SPVC) and soft permanent virtual path (SPVP), and Multiprotocol Label Switching (MPLS) servicesChassis CompatibilityCisco MGX 8830/B, MGX 8850, MGX 8850/B, MGX 8880, and MGX 8950Software CompatibilityCisco MGX 8800/8900 Software Release 5.2.00 and above for Cisco MGX 8830/B, MGX 8850, MGX 8850/B, and MGX 8950Cisco MGX 8800/8900 Software Release 5.3.00 and above for Cisco MGX 8880ProtocolsATM and SONET/SDHPort Density8 ports (4 ports at full line rate on the Cisco MGX 8800 chassis)Network ManagementManaged by Cisco WAN Manager software suiteBased on Simple Network Management Protocol (SNMP)PowerInput power required: -48 VDC Power consumption: 134WPhysical DimensionsH x D: 15.83 x 15.65 in. (40.20 x 39.75 cm)Weight6.5 lb (2.95 kg)

Key feattures :The Cisco MGX-XM60 Switching Module has the following primary features:Single-height card60-Gbps nonblocking crosspoint switch fabricDynamic sharing of capacity across multiple Cisco XM-60s, allowing for N + 1 redundancyFour installed in each Cisco MGX 8950 for 240-Gbps total capacity, 180-Gbps redundant capacityHot card insertion/removalComplete separation from control processor, allowing data forwarding in the event of control card failureChassis compatibilityMGX 8950Software compatibilityMGX S/W Releases supporting MGX-XM60:MGX Rls 4.0.15 and aboveNetwork managementManaged by Cisco WAN Manager Software suiteBased on Simple Network Management Protocol (SNMP)PowerInput power required: -48 VDCPower consumption: 61 WPhysical dimensionsH x D: 7.25 x 16.5 in. (18.41 x 41.91 cm)Weight3.5 lb

AXSM can be used in the MGX 8850 to provide ATM capability up to OC-48c/STM-16.High scalability in interface speeds with T3/E3 ports, OC-3c/STM-1, OC-12c/STM-4, and OC-48c/ STM-16 AXSM modules. Each port on the AXSM can be configured for either trunk or access applications.Industry leading module port densities of 16 T3/E3 ports, 16 OC-3c/STM-1 ports, 4 OC-12c/STM-4 ports, and 1 OC-48c/ STM-16 port that can scale up to 12 OC-48c/STM-16 modules in each MGX 8850 Multiservice Switch. Each OC-48c/STM-16 delivers fully nonblocking, full duplex throughput, in which a connection can occupy the entire line rate.Support for all ATM service classes, with up to 16 classes of service (CoS). Supports carrier-class implementation of standards-based PNNI, SVC/SVP, SPVC/SPVP, and MPLS services. Large cell buffers (one million cells), which help to maximize "goodput" performance during congestion, reducing the number of retransmits; the buffers are allocated dynamically, depending on connection resource needs, thereby optimizing use of system resources.High reliability with hot-standby 1:1 AXSM card redundancy, 1:1 and 1+1 line redundancy using APS. Ports and trunks supported on same AXSM moduleUser-Network Interface (UNI) Specifications 3.0, 3.1, 4.0Network Management Management using Cisco WAN Manager software suiteBased on Simple Network Management Protocol (SNMP)Physical SpecificationsDimensions: (H x D) 15.83 x 15.65 in.Electrical SpecificationsInput power required: -48 VDCPower consumption: 95W

Key Features: The main features of the Cisco MGX 8800/8900 16-Port OC-3c/STM-1 ATM Switch Service Module are listed here.Full nonblocking, full-duplex line-rate throughput on all 16 portsHigh reliability with hot-standby 1+1 16-port ATM switch service module card redundancyPer-virtual-path and per-virtual-circuit traffic shaping and available bit rate (ABR) with virtual source and virtual destinationY-cable and APS (1:1 and 1+1) port redundancy, plus APS 1+1 card redundancyUp to 4 million cell buffersUp to 16 classes of service (CoS) that can be used to support IP or ATM servicesSupport for standards-based Private Network-to-Network Interface (PNNI), switched virtual circuit (SVC) and switched virtual path (SVP), soft permanent virtual connection (SPVC) and soft permanent virtual path (SPVP), and Multiprotocol Label Switching (MPLS) servicesChassis Compatibility: Cisco MGX 8830/B, MGX 8850, MGX 8850/B, and MGX 8950Software Compatibility: Cisco MGX 8800/8900 SW Release 5.0.20 and aboveProtocols : ATM and SONET/SDHPort Density : 16 portsNetwork Management Managed by Cisco WAN Manager software suite Based on Simple Network Management Protocol (SNMP)PowerInput power required: -48 VDCPower consumption: 114WPhysical DimensionsH x D: 15.83 x 15.65 in. (40.20 x 39.75 cm)Weight6.5 lb (2.95 kg)

Ports : 48 x 10/25-Gbps and 6 x 40/100-Gbps QSFP28 portsDownlink supported speeds : 1/10/25-Gbps speedsCPU: 4 coresSystem memory: 24 GBSSD drive : 64 GBSystem buffer: 40 MBManagement ports 2 ports: 1 RJ-45 and 1 SFPUSB ports : 1RS-232 serial ports :  1Power supplies (up to 2) : 650W AC, 930W DC, or 1200W HVAC/HVDCTypical power (AC/DC) :  210WMaximum power (AC/DC) :  470WPhysical dimensions c(H x W x D)1.72 x 17.3 x 22.5 in.(4.4 x 43.9 x 57.1 cm)Weight (without power supplies or fans) 17.2 lb (7.8 kg)N9K-C93180YC-EX is one of the Cisco Nexus 9300-EX switches. Cisco Nexus 9300-EX platforms are the next generation of fixed Cisco Nexus9000 Series Switches. The new platforms support cost-effective cloud-scale deployments, an increased number of endpoints, and cloud serviceswith wire-rate security and telemetry. The platforms are built on modern system architecture designed to provide high performance and meetthe evolving needs of highly scalable data centers and growing enterprises.

Device Type : Switch - 24 ports - L3Enclosure Type : Rack-mountable 1USubtype : 50 Gigabit EthernetPorts : 24 x 40/50 Gigabit QSFP+ + 6 x 40/100 Gigabit QSFP+Performance : Bandwidth: 3.6 Tbps ¦ Active SPAN sessions: 4Capacity : Multiple Spanning Tree Protocol instances: 64 ¦ HSRP groups: 490 ¦ Per VLAN Rapid Spanning Tree instances: 4000 ¦ Maximum number of links in a port channel: 32 ¦ Maximum number of port channels: 512 ¦ ECMP paths: 64 ¦ Virtual Routing and Forwarding (VRF) instances: 1000 ¦ VLANs supported: 4096 ¦ ACL entries (egress): 2000 ¦ ACL entries (ingress): 4000 ¦ IGMP snooping groups: 8000 ¦ Multicast routes: 8000MAC Address Table Size : 512K entriesRouting Protocol :OSPF, RIP, RIP-2, BGP, EIGRP, HSRP, PIM-SM, MSDP, ECMP, MPLSFeatures : Layer 3 switching, High Availability, hot swappable 4 fans, Virtual PortChannel (vPC) technology, In-Service Software Upgrade (ISSU), NPV Gateway mode, Virtual Extensible LAN (VXLAN), Source-Specific Multicast (SSM), Ethernet Virtual Private Network (EVPN), 40MB system bufferRAM : 24 GBBuilt-in Devices : 64 GB SSDThe Cisco Nexus 93180LC-EX Switch is the industry's first 50-Gbps capable 1RU switch that supports 3.6 Tbps of bandwidth and over 2.6 bpps across 24 fixed 40/50-Gbps QSFP+ ports. Ports numbered 25, 27, 29, 30, 31, and 32 are the 6 uplinks ports, which can be configured as 40- and 100-Gbps ports, offering flexible migration options. This switch is capable of supporting flexible port configurations.

Ports :  16 x 400/100/40-Gbps QSFP-DD portsSystem memory :  16 GB NX-OS, 24 GB ACISolid-State Disk (SSD) :  128 GBUSB  1 portRS-232 serial console ports 1Management ports 2 (1 x 10/100/1000BASE-T and 1 x 1-Gbps SFP+)Broadwell-DE CPU 4 coresDimensions (H x W x D) 3.38 x 17.37 x 22.27 in. (8.59 x 44.13 x 56.58 cm)N9K-C9316D-GX is the Cisco Nexus 9316D Spine switch with 16p 400/100G QSFP-DD. Based on Cisco® Cloud Scale technology, the CiscoNexus® 9300-GX switches are the next generation of fixed Cisco Nexus 9000 Series Switches. The platform introduces a fully backwardcompatible 400G optical interface Quad Small Form-Factor Pluggable – Double Density (QSFP-DD) to transparently migrate existing data centerfabrics from 40-Gbps and 100-Gbps speeds to 400 Gbps. The platform provides investment protection for customers, delivering highly flexiblelayer 2 and layer 3 scalability, and performance to meet the changing needs of virtualized data centers and automated cloud environments.

Ports  : 28 x 100/40-Gbps QSFP28 ports and 8 x 400/100-Gbps QSFP-DD portsSystem memory :  16 GB NX-OS, 24 GB ACISolid-State Disk : (SSD) 128 GBUSB : 1 portRS-232 serial console ports  : 1Management ports : 2 (1 x 10/100/1000BASE-T and 1 x 1-Gbps SFP+)Broadwell-DE CPU  : 4 coresDimensions (H x W x D) 1.72 x 17.37 x 25.5 in. (4.37 x 44.13 x 64.8 cm)N9K-C93600CD-GX is the Cisco Nexus 9316D Spine and Leaf switch with 28p 100/40G QSFP28 and 8p 400/100G QSFP-DD. Based on CiscoCloud Scale technology, the Cisco Nexus 9300-GX switches are the next generation of fixed Cisco Nexus 9000 Series Switches. The platformintroduces a fully backward-compatible 400G optical interface Quad Small Form-Factor Pluggable – Double Density (QSFP-DD) to transparentlymigrate existing data center fabrics from 40-Gbps and 100-Gbps speeds to 400 Gbps. The platform provides investment protection forcustomers, delivering highly flexible layer 2 and layer 3 scalability, and performance to meet the changing needs of virtualized data centers andautomated cloud environments.

Features and CapabilitiesThe Cisco Nexus 9504 Switch offers a comprehensive feature set, high resiliency, and a broad range of high performance Gigabit Ethernet line cards. It can meet the most demanding requirements of enterprise, service provider, and cloud data centers.Deployment FlexibilitySupport for the next-generation data center based on Cisco ACINexus Fabric Manager support to automate fabric configuration and managementTraditional data centers in standalone NX-OS modeProgrammabilityOpen API to manage the switch through remote-procedure calls (JavaScript Object Notation or XML) over HTTP or HTTPSAutomated configuration through Linux shell scriptsSupport for customer applications through a Linux container environmentProgrammable APIs for integration with DevOps automation toolsHigh AvailabilityIn-Service Software Upgrade (ISSU) and patching without operation interruption Redundant and hot-swappable supervisors, system controllers, power supplies, and fan traysMix of third-party and Cisco application-specific integrated circuits (ASICs) for improved reliabilityEnergy EfficiencyDesigned without a midplane to optimize front-to-back airflow and reduce power consumptionOptimized design with fewer ASICs, resulting in lower energy useEfficient power supplies that are rated at 80 Plus Platinum Nonblocking performance 15 Tbps10 Gigabit Ethernet nonblocking ports Up to 51225 Gigabit Ethernet Ports Up to 51250 Gigabit Ethernet Ports Up to 25640/100 Gigabit Ethernet nonblocking ports Up to 1441/10GBASE-T nonblocking ports Up to 192Form factor 7-rack-unit chassisLine card slots 4Airflow Front to back

Features and CapabilitiesThe Cisco Nexus 9508 Switch offers a comprehensive feature set, high resiliency, and a broad range of 1/10/40 Gigabit Ethernet line cards to meet the mostdemanding requirements of enterprise, service provider, and cloud data centers.ACI SupportDesigned to support the Cisco next-generation data center based on Cisco ACIProgrammabilityOpen API to manage the switch through remote-procedure calls (JavaScript Object Notation or XML) over HTTP or HTTPSAutomated configuration through Linux shell scriptsSupport for customer applications through a Linux container environmentHigh AvailabilityFull Cisco In-Service Software Upgrade (ISSU) and patching supportRedundant and hot-swappable supervisors, system controllers, power supplies, and fan traysMix of third-party and Cisco application-specific integrated circuits (ASICs) for improved reliabilityEnergy EfficiencyDesign without a midplane to optimize front-to-back airflow and reduce power consumptionOptimized design with fewer ASICs, resulting in lower energy useEfficient power supplies that are rated at 80 Plus PlatinumSpecifications at a Glance30 Tbps of nonblocking performanceUp to 1152 10 Gigabit Ethernet nonblocking portsUp to 288 40 Gigabit Ethernet nonblocking portsUp to 384 1/10GBASE-T nonblocking ports13-rack-unit chassis8 line card slotsFront-to-back airflow

Features and capabilities: The Cisco Nexus 9516 Switch offers a comprehensive feature set, high resiliency, and a broad range of 1/10/40 Gigabit Ethernet line cards. It can meet the most demanding requirements of enterprise, service provider, and cloud data centers.Cisco ACI supportDesigned to support the Cisco next-generation data center based on Cisco ACIProgrammabilityOpen API to manage the switch through remote-procedure calls (JavaScript Object Notation or XML) over HTTP or HTTPSAutomated configuration through Linux shell scriptsSupport for customer applications through a Linux container environmentHigh availabilitySoftware patching for continued operationsRedundant and hot-swappable supervisors, system controllers, power supplies, and fan traysMix of third-party and Cisco application-specific integrated circuits (ASICs) for improved reliabilityEnergy efficiencyDesign without a midplane to optimize front-to-back airflow and reduce power consumptionOptimized design with fewer ASICs, resulting in lower energy useEfficient power supplies that are rated at 80 Plus PlatinumInvestment protection40 Gb  for reuse of existing 10 Gigabit Ethernet multimode cabling plant for 40 Gigabit EthernetSupport for Cisco NX-OS and Cisco ACI modes of operationSupport for Cisco Nexus 2000 Series Fabric ExtendersForm factor : 21 RULine card slots : 16Supervisor slots : 2Fabric module slots : 6ACI support :YesBandwidth per slot (Tbps) : 3.84Bandwidth per system (Tbps) : 60Maximum number of 1/10G BASE-T ports : 768Maximum number of 10 GE ports : 2304Maximum number of 40 GE ports : 576Maximum number of 100GE ports : 576Airflow : Front to backPower supplies (3-kW AC/DC) : Up to 10Fan trays : 3

Key feattures :The Cisco MGX-XM60 Switching Module has the following primary features:Single-height card60-Gbps nonblocking crosspoint switch fabricDynamic sharing of capacity across multiple Cisco XM-60s, allowing for N + 1 redundancyFour installed in each Cisco MGX 8950 for 240-Gbps total capacity, 180-Gbps redundant capacityHot card insertion/removalComplete separation from control processor, allowing data forwarding in the event of control card failureChassis compatibilityMGX 8950Software compatibilityMGX S/W Releases supporting MGX-XM60:MGX Rls 4.0.15 and aboveNetwork managementManaged by Cisco WAN Manager Software suiteBased on Simple Network Management Protocol (SNMP)PowerInput power required: -48 VDCPower consumption: 61 WPhysical dimensionsH x D: 7.25 x 16.5 in. (18.41 x 41.91 cm)Weight3.5 lb

Key FeaturesThe main features of the Cisco 8-Port OC-12/STM-4 Channelized/Unchannelized ATM Switch Service Module are listed here.Full nonblocking, full-duplex line-rate throughput on all 8 ports when used on the Cisco MGX 8950 chassisUp to 4 ports with nonblocking, full-duplex line-rate throughput when used on the Cisco MGX 8800 chassisIndividual port channelization down to DS-3 and OC-3c/STM-1Per-virtual-path and per-virtual-circuit traffic shaping and available bit rate (ABR) with virtual source and virtual destinationAPS (1:1 and 1+1) port redundancy, plus APS 1+1 card redundancyUp to 4 million cell buffersUp to 16 classes of service (CoS) that can be used to support IP or ATM servicesSupport for standards-based Private Network-to-Network Interface (PNNI), switched virtual circuit (SVC) and switched virtual path (SVP), soft permanent virtual connection (SPVC) and soft permanent virtual path (SPVP), and Multiprotocol Label Switching (MPLS) servicesChassis CompatibilityCisco MGX 8830/B, MGX 8850, MGX 8850/B, MGX 8880, and MGX 8950Software CompatibilityCisco MGX 8800/8900 Software Release 5.2.00 and above for Cisco MGX 8830/B, MGX 8850, MGX 8850/B, and MGX 8950Cisco MGX 8800/8900 Software Release 5.3.00 and above for Cisco MGX 8880ProtocolsATM and SONET/SDHPort Density8 ports (4 ports at full line rate on the Cisco MGX 8800 chassis)Network ManagementManaged by Cisco WAN Manager software suiteBased on Simple Network Management Protocol (SNMP)PowerInput power required: -48 VDC Power consumption: 134WPhysical DimensionsH x D: 15.83 x 15.65 in. (40.20 x 39.75 cm)Weight6.5 lb (2.95 kg)

Key Features64-bit MIPS-based processor operating at 700 MHz45-Gbps switch fabric and 1.2-Gbps cell-bus (when used with chassis other than the Cisco MGX 8950)Cisco PXM-45/C used only as processor in Cisco MGX 8950; Cisco MGX-XM-60 provides switch-fabric function in that chassisHot swappable1:1 hot-standby redundancyUser-selectable primary and secondary clock sources with graceful switchoverInternal Stratum-3, external Building Integrated Timing Supply (BITS), or in-band clock sourcesIn-band or out-of-band management using EIA/TIA-232 or 10BASE-T control portsSupport for narrowband and broadband service modules scaling from DS-0 to OC-48c/STM-16 or DS-3/E3 to OC-192/STM-64 (depending on the chassis used)Chassis compatibilityCisco MGX 8830/B, MGX 8850, MGX 8850/B, MGX 8880, and MGX 8950Software compatibilityMinimum Cisco MGX software release supporting Cisco PXM-45/C:Cisco MGX 8850 Software Release 4.0.15Cisco MGX 8950 Software Release 4.0.15 Cisco MGX Software Release 5.0.20 (for Cisco MGX 8880 and MGX 8850/B)Cisco MGX Software Release 5.2.00 (for Cisco MGX 8830/B)Network Management Managed by Cisco WAN Manager Software suite Based on Simple Network Management Protocol (SNMP)PowerInput power required: -48 VDCPower consumption: 128 WPhysical DimensionsH x D: 15.75 x 16.5 in. (40.00 x 41.91 cm)Weight6.5 lbs

Key Features: The main features of the Cisco MGX 8800/8900 16-Port OC-3c/STM-1 ATM Switch Service Module are listed here.Full nonblocking, full-duplex line-rate throughput on all 16 portsHigh reliability with hot-standby 1+1 16-port ATM switch service module card redundancyPer-virtual-path and per-virtual-circuit traffic shaping and available bit rate (ABR) with virtual source and virtual destinationY-cable and APS (1:1 and 1+1) port redundancy, plus APS 1+1 card redundancyUp to 4 million cell buffersUp to 16 classes of service (CoS) that can be used to support IP or ATM servicesSupport for standards-based Private Network-to-Network Interface (PNNI), switched virtual circuit (SVC) and switched virtual path (SVP), soft permanent virtual connection (SPVC) and soft permanent virtual path (SPVP), and Multiprotocol Label Switching (MPLS) servicesChassis Compatibility: Cisco MGX 8830/B, MGX 8850, MGX 8850/B, and MGX 8950Software Compatibility: Cisco MGX 8800/8900 SW Release 5.0.20 and aboveProtocols : ATM and SONET/SDHPort Density : 16 portsNetwork Management Managed by Cisco WAN Manager software suite Based on Simple Network Management Protocol (SNMP)PowerInput power required: -48 VDCPower consumption: 114WPhysical DimensionsH x D: 15.83 x 15.65 in. (40.20 x 39.75 cm)Weight6.5 lb (2.95 kg)

AXSM can be used in the MGX 8850 to provide ATM capability up to OC-48c/STM-16.High scalability in interface speeds with T3/E3 ports, OC-3c/STM-1, OC-12c/STM-4, and OC-48c/ STM-16 AXSM modules. Each port on the AXSM can be configured for either trunk or access applications.Industry leading module port densities of 16 T3/E3 ports, 16 OC-3c/STM-1 ports, 4 OC-12c/STM-4 ports, and 1 OC-48c/ STM-16 port that can scale up to 12 OC-48c/STM-16 modules in each MGX 8850 Multiservice Switch. Each OC-48c/STM-16 delivers fully nonblocking, full duplex throughput, in which a connection can occupy the entire line rate.Support for all ATM service classes, with up to 16 classes of service (CoS). Supports carrier-class implementation of standards-based PNNI, SVC/SVP, SPVC/SPVP, and MPLS services. Large cell buffers (one million cells), which help to maximize "goodput" performance during congestion, reducing the number of retransmits; the buffers are allocated dynamically, depending on connection resource needs, thereby optimizing use of system resources.High reliability with hot-standby 1:1 AXSM card redundancy, 1:1 and 1+1 line redundancy using APS.Ports and trunks supported on same AXSM moduleUser-Network Interface (UNI) Specifications 3.0, 3.1, 4.0Network ManagementManagement using Cisco WAN Manager software suiteBased on Simple Network Management Protocol (SNMP)Physical SpecificationsDimensions: (H x D) 15.83 x 15.65 in.Electrical SpecificationsInput power required: -48 VDCPower consumption: 95W

ApplicationsHigh-density broadband ATMScaling MPLS servicesConvergence of voice and data networksTechnical SpecificationsThe following are some of the key features of the Cisco MGX 8950 Multiservice Switch:Scalability of up to 180-Gbps fully redundant nonblocking switching within a single chassis10-Gbps ATM interfaces (OC-192c/STM-64) Industry-leading broadband densityOC-3c/STM-1, OC-12c/STM-4, and OC-48c/STM-16 trunk aggregationIndustry's highest network availabilitySoftware compatibility MGX 4.0.15 release and later (depending on the service modules configured)Service module compatibilityAXSM-16-155-XG, AXSM-8-622-XG, AXSM-4-2488-XG, AXSM-1-9953-XGAXSM-16-T3E3/B, AXSM-1-2488/BMGX-RPM-PR-256, MGX-RPM-PR-512, MGX-RPM-XF-512Control cardPXM45/C Processor Switching Module (only processor function is used)Redundant slots 7 and 8 reserved for control cardSlotsControl processor slots: 2 fixed double-height slots for primary and secondarySwitching card slots: 2 fixed double-height slots divided into 4 single-height slots for 4 load-sharing XM60 switching cardsService module slots: 12 double-height slotsConnectivityT3/E3, OC-3/STM1, OC-12/STM-4, OC-48/STM-16, OC-192/STM-64, POS, Ethernet, Fast Ethernet, Gigabit EthernetNetwork management interfacesRJ-45 Ethernet port for the management interface at the node, and In-band ATM connection to reach remote node for management connectivity,DB-15 for the visual and audible alarm port, a command-line interface (CLI) for local management, Simple Network Management Protocol (SNMP) for the network management system interface, Secure File Transfer Protocol (SFTP) for file transfer,and Secure Shell (SSHv1 and SSHv2) Protocol for remote CLI accessPhysical dimensions(H x W x D): 35 x 19 x 22 inches (88.9 x 48.26 x 55.88 cm)Rack-mountable in 19- and 23-inch EIA/RETMA and ETSI racksPowerTypical consumption: 5 kW for maximum configuration system

Key FeaturesThe main features of the Cisco MGX 8950 OC-192c/STM-64 ATM Switch Service Module are listed here.Full nonblocking, full-duplex line-rate throughputHigh reliability with hot-standby 1+1 ATM switch service module card redundancyPer-virtual-path and per-virtual-circuit traffic shaping and available bit rate (ABR) with virtual source and virtual destinationUp to 4 million cell buffersUp to 16 classes of service (CoS) that can be used to support IP or ATM servicesSupport for standards-based Private Network-to-Network Interface (PNNI), switched virtual circuit (SVC) and switched virtual path (SVP), soft permanent virtual connection (SPVC) and soft permanent virtual path (SPVP), and Multiprotocol Label Switching (MPLS) servicesChassis Compatibility : Cisco MGX 8950Software Compatibility : Cisco MGX Software Release 4.0.15 and aboveProtocols : ATM and SONET/SDHPort Density : 1 portLayer 1 (Physical Layer) Feature SummaryUser-Network Interface (UNI) 3.0, 3.1, and 4.0 physical layer specificationsCompliance with the following SONET standards:Bellcore GR-253-COREANSI T1.105Compliance with the following SDH standards:ITU-T G.707, G.708, G.709, and G.783ITU-T G.957 and G.958Additional Physical Layer Specifications for Ports and OpticsNetwork Management : Managed by Cisco WAN Manager software suiteBased on Simple Network Management Protocol (SNMP)Power : Input power required: -48 VDCPower consumption: 205WPhysical Dimensions : H x D: 15.83 x 15.65 in. (40.20 x 39.75 cm)Weight : 6.5 lb (2.95 kg)

Brand : Cisco Systems, Inc. Series : 350 Model : SF350-48-K9-NA Format : Desktop Network Management Type : Ethernet Switch Uplink Ports: Yes Uplink Interface : SFP Primary Ports : 48 x Fast Ethernet Network Fast Ethernet Gigabit Ethernet 2 x Gigabit Ethernet Expansion Slot 4 x Gigabit Ethernet Network Primary Port Speed: 10/100Base-TX 1000Base-X 10/100/1000Base-TX Data Transmission Speed :  SFP Weight : 10.4

Brand : Cisco Systems, Inc. Series : 350 Model : SF350-48P-K9-NA Format : Desktop Network Management Type : Ethernet Switch Uplink Ports : Yes Uplink Interface : SFP Primary Ports : 48 x Fast Ethernet Network Fast Ethernet 4 x Gigabit Ethernet Expansion Slot Gigabit Ethernet 2 x Gigabit Ethernet Network Primary Port Speed : 10/100Base-TX 1000Base-X 10/100/1000Base-TX Data Transmission Uplink Speed : SFP Weight : 15.9

Brand : Cisco Systems, Inc. Series : 350 Model : SF350-48MP-K9-NA Format : Desktop Network Management Type : Ethernet Switch Uplink Ports : Yes Uplink Interface : SFP Primary Ports : 48 x Fast Ethernet Network Fast Ethernet Gigabit Ethernet 4 x Gigabit Ethernet Expansion Slot 2 x Gigabit Ethernet Network Primary Port Speed : 10/100Base-TX 1000Base-X 10/100/1000Base-TX Data Transmission Uplink Speed : SFP Weight : 16.2 Model : SF350-48MP

Part Number N9K-C92160YC-XPorts : 48 x 10- and 25-Gbps SFP+ and 6 QSFP+ ports (4 are 100-Gbps capable)Supported speeds :1, 10, and 25 Gbps on SFP+ ports10, 25, 40, and 100 Gbps on QSFP+ portsPort configuration :48 x 10/25-Gbps ports for downlinks; 4 of the 6 uplink ports are 100-Gbps capable. Ports 50 and 52 can beindividually configured into 1 x 100 Gbps, 4 x 10 Gbps, 4 x 25 Gbps, 1 x 40 Gbps, or 2 x 50 GbpsCPU :2 coresSystem memory : 16GSSD drive :24GShared system buffer :20MBManagement ports 2 ports: 1 RJ-45 and 1SFPUSB ports 1RS-232 serial ports :  1Power supplies (up to 2) :650W AC, 930W DC, or 1200W AC/HVDCPhysical dimensions :(H x W x D)1.72 x 17.3 x 22.5 in. (4.4 x 43.9 x 57.1 cm)Weight (without power supplies or fans)14.12 lb (6.4 kg)(1) Power Supply (2) 4 x Fan Module (3) Power Supply(4) Out-of-band management port (RJ-45 port)(5) Chassis LEDs (Beacon [BCN] and Status [STS])(6) USB port used for saving or copying functions (7) Out-of-band management port (SFP port)(8) Console port (RS232 port)

N9K-C92160YC-X is one of the Cisco Nexus 9200 switches. 92160YC-X Switch is optimized for Cisco NX-OS deployments. It provides 48 1/10/25-Gb host ports and up to six hybrid uplink ports that can be configured as 10, 25, 40, or 100-Gb ports. With 3.2 Tbps of switching capacity, the92160YC-X delivers line-rate Layer 2 and 3 features for demanding enterprise, service provider hosting, and cloud computing environments.

The Cisco Nexus 92304QC switch (N9K-C92304QC) is a 2-RU switch with the following ports:56 fixed 40-Gigabit QSFP+ (optical) interface ports supporting 1-, 10-, and 40-Gigabit speeds16 of these ports support breakout cables for connections to 64 1- and 10-Gigabit ports on other devices.8 QSFP28 ports supporting 40- and 100-Gigabit speeds1 console port1 management port2 software-defined ports (labeled as S1-65 and S1-66)1 USB port

The Cisco Nexus 93360YC-FX2 Leaf Switch is a 2-Rack-Unit (2RU) Leaf switch that supports 7.2 Tbps of bandwidth and 2.8 bpps across 96 fixed 10/25G SFP+ ports and 12 fixed 40/10G QSFP28 ports. The 96 ports of downlinks support 1/10/25-Gbps. The 12 uplinks ports can be configured as 40- and 100-Gbps ports, offering flexible migration options. The switch is ideal for a non-oversubscribed solution in a compact form factor. The switch has FC-FEC and RS-FEC enabled for 25Gbps support over longer distances.Main FeaturesFX2SwitchL3managed96 x 1/10/25 Gigabit SFP+ + 12 x 40/100 Gigabit QSFP28rack-mountableBuilt-in Devices :128 GB SSDInstalled Size :16 GBCapacity :SPAN sessions: 4, Port channels: 512, VLANs supported: 3967, NAT entries: 1023, HSRP groups: 490, Longest prefix match (LPM) routes: 896000, Multicast routes: 32000, ACL entries (ingress): 5000, MST instances: 64, ECMP paths: 64, IP host entries: 896000, ACL entries (egress): 2000, MAC addresses: 256000, Rapid Per-VLAN Spanning Tree Plus instances: 3967Form Factor :Rack-mountablePorts Qty :96Advanced Switching :Layer 3Routing Protocol :ECMP, RSVP, BGP, PIM-SM, MSDP, OSPF, EIGRP, RIP, RIP-2, Multiprotocol BGP, HSRP, MPLSManageable :YesStatus Indicators :StatusFeatures :Layer 3 switching, Open Shortest Path First (OSPF), 3 fans, Port-side exhaust (PSE), Multicast Source Discovery Protocol (MSDP), MPLS support, Virtual Extensible LAN (VXLAN), MACsec support, Source-Specific Multicast (SSM), Access Control List (ACL) support, Virtual PortChannel (vPC) technology, 40MB system buffer, Spanning Tree Protocol (STP) support, Power On Auto Provisioning (POAP), Ethernet Virtual Private Network (EVPN), Multiple Spanning Tree Protocol (MSTP) supportInterfaces :1 x management SFP+, 12 x 100Gbit/40Gbit LAN QSFP28, 96 x 1/10/25Gbit LAN SFP+, 1 x serial (RS-232), 1 x USB, 1 x management RJ-45Ports Type :40/100 Gigabit QSFP28Dimensions & WeightWidth :17.4 inchDepth :22.9 inchHeight :3.4 inch

The Cisco Nexus 9336C-FX2 offers flexible port speeds in a compact form factor. Designed to meet the changing needs of data centers, big data applications, and automated cloud environments, this powerful switch delivers superior programmability.Main Features : FX2SwitchL3managed36 x 100 Gigabit QSFP28 / 40 Gigabit QSFP28rack-mountableBuilt-in Devices :128 GB SSDInstalled Size :24 GBPerformance :Bandwidth: 2.8 bpps, Bandwidth: 7.2 TbpsFeatures :Ethernet Virtual Private Network (EVPN), Port exhaust, 40MB system buffer, Spanning Tree Protocol (STP) support, Virtual PortChannel (vPC) technology, Multiple Spanning Tree Protocol (MSTP) support, Power On Auto Provisioning (POAP), 3 fan trays, Side intake airflow, Virtual Extensible LAN (VXLAN), Source-Specific Multicast (SSM), Access Control List (ACL) support, MACsec supportType :100 Gigabit QSFP28 / 40 Gigabit QSFP28Interfaces :1 x management RJ-45, 1 x USB, 36 x 100Gbit/40Gbit LAN QSFP28, 1 x management SFP+, 1 x serial (RS-232)Type :Internal power supplyPower Redundancy :OptionalInstalled Qty :0Max Supported Qty :2Nominal Voltage :AC 120/230 VFrequency Required :50/60 hertzPower Consumption Operational :777 wattDimensions & WeightWidth :17.3 inchDepth :24.5 inchHeight :1.7 inchWeight :18.74 lbs

Architectural flexibility : Support for Cisco ACI architecture and NX-OS48 x 1/10/25 Gbps fiber ports12 x 40/100 Gbps QSFP28 portsSupports 4.8 Tbps of bandwidth and over 1.8 bppsRich features : Automated, policy-based systems management with Cisco ACIBuild programmable SDN fabrics leveraging open APIs and over 65 Cisco ACI global technology partnersEnhanced Cisco NX-OS Software designed for performance, resiliency, scalability, manageability, and programmabilityReal-time buffer utilization per port and per queue, for monitoring traffic micro-bursts and application traffic patternsHighly available and efficient design : High-performance, Layer 2 and 3 non-blocking architectureEasily deployed into either a hot-aisle or cold-aisle configurationRedundant, hot-swappable power supplies and fan traysSpecifications at a Glance : Powered by cloud-scale technology48 x 1/10/25 Gbps fiber ports12 x 40/100 Gbps QSFP28 ports40 MB bufferUp to 4.8 Tbps of bandwidth

The Cisco Nexus 9348GC-FXP Switch is a 1RU switch that supports 696 Gbps of bandwidth and over 250 mpps. The 48 1GBASE-T downlink ports on the switch can be configured to work as 100-Mbps, 1-Gbps ports. The 4 ports of SFP28 can be configured as 1/10/25-Gbps and the 2 ports of QSFP28 can be configured as 40- and 100-Gbps ports.Cisco Nexus 9348GC-FXP Switch is designed to meet the changing needs of data centers, big data applications, and automated cloud environments.Highlights points: Powered by Cisco Cloud Scale ASIC technologySupport for Cisco NX OS Software and Cisco ACI (Application Centric Infrastructure) architectureHigh-performance, Layer 2 and 3 non-blocking architectureEasily deployed into either a hot-aisle or cold-aisle configurationCisco Tetration Analytics Platform support with built-in hardware sensors for rich traffic flow telemetry and line-rate data collectionCisco Nexus Data Broker support for network traffic monitoring and analysisRobust hardware system specifications feature 4-core CPU, 24 GB of system memory, and respectively 128-GB SSD driveThe 40-MB buffer supporting highly scalable data centers and big data applications 696 Gbps of bandwidth and over 250 mppsFixed downlinks with 48 x FE/GEFixed uplinks with 4 x 25GE SFP28, 2 x 100GE QSFP28

Physical : 64-port 40/100G QSFP28 ports & 2-port 1/10G SFP+ ports1200 watt (W) AC power supplies or 930W DC power supplies (up to 2)Hot-swappable, dual fan trays with redundant fansSystem memory: 32GBSSD: 256GBUSB: 1 portRS-232 serial console ports: 1(1) 1-/10-Gigabit SFP+ ports (2)(2) 40-/100-Gigabit QSFP28 ports (ports 1 to 48 in 4 rows of 12 ports)(3) Green colored 40-/100-Gigabit QSFP28 ports supporting MACsec (when software support is available) (ports 49 to 64 in 4 rows of 4 ports)(4) Fan modules (3) with slots numbered from 1 (left) to 3 (right)(5) USB port (1)(6) Management port (1—SFP optical port)(7) Management port (1—RJ-45 copper port)(8) Power supply modules (1 or 2) (AC power supplies shown) with slots numbered 1 (top) and 2 (bottom)(9) Console port (1)Management ports:2 (1 x 10/100/1000BASE-T and 1 x 1-Gbps SFP+)Broadwell-DE CPU: 4 coresPhysical (H x W x D) 3.38 x 17.37 x 22.27 in. (8.59 x 44.13 x 56.58 cm)Weight (chassis) 36.9lb (16.74kg) with power supplies and fans, 27.4 lb (12.43kg) without power supplies and fans

Ports :32 QSFP+ portsSupported speeds :40 Gigabit Ethernet speedsPhysical: (H x W x D) 1.72 x 17.3 x 22.5 in. (4.4 x 43.9 x 57.1 cm)Weight 22 lb (10.0 kg) (without power supplies or fans)Predictable highperformance : Latency of 1 to 2 microseconds with up to 1.28 Tbps of bandwidth enables customers to build a robust switch fabric scalingfrom as few as 200 10-Gbps server ports to more than 200,000 10-Gbps server ports.Increased integrated buffer space : Up to a total of 50 MB of integrated shared buffer space allows better management of speed mismatch between access anduplink ports.Designed for availability : Hot-swappable, redundant power supplies and fan trays increase availability.Flexible airflow configuration: Port-side intake and port-side exhaust airflow configurations are both supported.CPU, SSD,and memory : Dual-core 2.5-GHz x86 CPUs with 64-GB SSD drive and 16 GB of memory provide enhanced network performance.Power efficiency : All Cisco Nexus 9000 Series power supplies are 80 Plus Platinum rated.Advanced optics : Cisco offers a pluggable 40 Gigabit Ethernet QSFP+ transceiver that enables customers to use existing 10 Gigabit Ethernetdata center cabling to support 40 Gigabit Ethernet connectivity. This technology facilitates adoption of 40 Gigabit Ethernetwith no cable infrastructure upgrade cost.

Ports :32 QSFP+ portsSupported speeds :40 Gigabit Ethernet speedsPhysical: (H x W x D) 1.72 x 17.3 x 22.5 in. (4.4 x 43.9 x 57.1 cm)Weight 22 lb (10.0 kg) (without power supplies or fans)Predictable highperformance : Latency of 1 to 2 microseconds with up to 1.28 Tbps of bandwidth enables customers to build a robust switch fabric scalingfrom as few as 200 10-Gbps server ports to more than 200,000 10-Gbps server ports.Increased integrated buffer space : Up to a total of 50 MB of integrated shared buffer space allows better management of speed mismatch between access anduplink ports.Designed for availability : Hot-swappable, redundant power supplies and fan trays increase availability.Flexible airflow configuration: Port-side intake and port-side exhaust airflow configurations are both supported.CPU, SSD,and memory : Dual-core 2.5-GHz x86 CPUs with 64-GB SSD drive and 16 GB of memory provide enhanced network performance.Power efficiency : All Cisco Nexus 9000 Series power supplies are 80 Plus Platinum rated.Advanced optics : Cisco offers a pluggable 40 Gigabit Ethernet QSFP+ transceiver that enables customers to use existing 10 Gigabit Ethernetdata center cabling to support 40 Gigabit Ethernet connectivity. This technology facilitates adoption of 40 Gigabit Ethernetwith no cable infrastructure upgrade cost

Device Type : Switch - 36 ports - L3 - managedEnclosure Type : Desktop, rack-mountable 2USubtype : 40 Gigabit EthernetPorts : 36 x 40 Gigabit QSFP+Performance : Bandwidth: 1.44 TbpsCapacity : Longest prefix match (LPM) entries (IPv4): 16000 ¦ Host table entries (IPv4): 88000 ¦ MAC addresses: 160000 ¦ IPv4 routes (Multicast): 32000 ¦ Virtual interfaces (VLANs): 4096 ¦ Equal-Cost Multipathing (ECMP) ways: 64 ¦ Multiple Spanning Tree Protocol instances: 64 ¦ Rapid Per-VLAN Spanning Tree Plus instances: 507 ¦ Virtual Routing and Forwarding (VRF) entries: 1000 ¦ IGMP snooping entries: 32000Jumbo Frame Support : YesRouting Protocol : IS-IS, BGP, EIGRP, HSRP, VRRP, OSPFv2, PIM-SM, OSPFv3, MSDP, static IPv4 routing, ECMP, Bidirectional Forwarding Detection (BFD), VRRPv3Remote Management Protocol :SNMP 1, SNMP 2, RMON, Telnet, SNMP 3, SSH-2Authentication Method : RADIUS, PAP, CHAP, TACACS+, MS-CHAP, MS-CHAP v.2Features : Flow control, modular design, load balancing, VLAN support, IGMP snooping, Syslog support, Weighted Round Robin (WRR) queuing, Broadcast Storm Control, Multicast Storm Control, Unicast Storm Control, Weighted Random Early Detection (WRED), Spanning Tree Protocol (STP) support, Rapid Spanning Tree Protocol (RSTP) support, Multiple Spanning Tree Protocol (MSTP) support, Access Control List (ACL) support, Quality of Service (QoS), RADIUS support, RDMA support, Virtual Route Forwarding-Lite (VRF-Lite), Uni-Directional Link Detection (UDLD), Rapid Per-VLAN Spanning Tree Plus (PVRST+), LLDP support, DHCP relay, Link Aggregation Control Protocol (LACP), Virtual Routing and Forwarding (VRF), Class of Service (CoS), DiffServ Code Point (DSCP) supportCompliant Standards : IEEE 802.3z, IEEE 802.1D, IEEE 802.1Q, IEEE 802.1p, IEEE 802.3x, IEEE 802.3ad (LACP), IEEE 802.1w, IEEE 802.3ae, IEEE 802.1s, IEEE 801.1p, IEEE 802.1ab (LLDP), IEEE 802.3ba

Product Type :  Ethernet SwitchInterfaces/PortsTotal Number of Network Ports :  48Uplink Port :  YesModular  : YesStack Port : NoPort/Expansion Slot Details : 48 x 10 Gigabit Ethernet NetworkPort/Expansion Slot Details :6 x 100 Gigabit Ethernet Expansion SlotMedia & PerformanceMedia Type Supported Optical FiberMedia Type Supported Twisted PairEthernet Technology 100 Gigabit EthernetEthernet Technology 10 Gigabit EthernetNetwork Technology 100GBase-XNetwork Technology 10GBase-TI/O ExpansionsNumber of Total Expansion Slots  : 6Expansion Slot Type :QSFP28Shared SFP Slot :NoNetwork & Communication : Layer Supported :  3Management & ProtocolsManageable  : YesPower Description : Power Source Power SupplyRedundant Power Supply Supported  : Yes

N9K-C93108TC-EX is one of the Cisco Nexus 9300-EX switches. Cisco Nexus 9300-EX platforms are the next generation of fixed Cisco Nexus9000 Series Switches. The new platforms support cost-effective cloud-scale deployments, an increased number of endpoints, and cloud serviceswith wire-rate security and telemetry. The platforms are built on modern system architecture designed to provide high performance and meetthe evolving needs of highly scalable data centers and growing enterprises.Ports :  48 x 10GBASE-T and 6 x 40/100-Gbps QSFP28 portsDownlink supported speeds :  100-Mbps and 1/10-Gbps speedsCPU : 4 coresSystem memory : 24 GBSSD drive : 64 GBSystem buffer  : 40 MBManagement ports 2 ports: 1 RJ-45 and 1 SFPUSB ports  : 1RS-232 serial ports : 1Power supplies (up to 2) :  650W AC, 930W DC, or 1200W HVAC/HVDCTypical power (AC/DC) :  290WMaximum power (AC/DC) : 499WPhysical dimensions(H x W x D)1.72 x 17.3 x 22.5 in.(4.4 x 43.9 x 57.1 cm)Weight (without power supplies or fans) 17.7 lb (8.0 kg)

Ports : 96 fixed 1/10GBASE-T and 6 QSFP+ portsSupported speeds :100 Megabit Ethernet and 1/10 Gigabit Ethernet speeds40 Gigabit Ethernet uplinkports : 6 fixed QSFP+ portsPhysical (H x W x D) 3.5 x 17.5 x 22.5 in. (8.9 x 44.5 x 57.1 cm)Weight 26 lb (11.8 kg) (without power supplies, fans, or uplink module)Predictable high performance : Latency of 1 to 2 microseconds with up to 1.28 Tbps of bandwidth enables customers to build a robust switch fabric scalingfrom as few as 200 10-Gbps server ports to more than 200,000 10-Gbps server ports.Increased integrated buffer space : Up to a total of 50 MB of integrated shared buffer space allows better management of speed mismatch between access anduplink ports.Designed for availability : Hot-swappable, redundant power supplies and fan trays increase availability.Flexible airflow configuration :Port-side intake and port-side exhaust airflow configurations are both supported.CPU, SSD, and memory : Dual-core 2.5-GHz x86 CPUs with 64-GB SSD drive and 16 GB of memory provide enhanced network performance.Power efficiency : All Cisco Nexus 9000 Series power supplies are 80 Plus Platinum rated.Advanced optics : Cisco offers a pluggable 40 Gigabit Ethernet QSFP+ transceiver that enables customers to use existing 10 Gigabit Ethernetdata center cabling to support 40 Gigabit Ethernet connectivity. This technology facilitates adoption of 40 Gigabit Ethernetwith no cable infrastructure upgrade cost.

Brand:Cisco Small Business Series:300 Series Model:SRW2048-K9-NA Format:Rackmount Mac Address Table:8k Network Managed Type:Managed Dimensions:17.35 x 17.3 x 1.75 inch Weight:8.62 lbs

orm Factor:external Type:Wireless access point Connectivity Technology:wireless Type:Wireless access point Connectivity Technology:wireless Data Link Protocol:IEEE 802.11a, IEEE 802.11ac Wave 2, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n Wireless Protocol:802.11a/b/g/n/ac Wave 2 Data Transfer Rate:5.2 Gbps Wi-Fi Bands: 2.4 GHz, 5 GHz Status Indicator:Boot state, error, status

Subcategory: power converters, splitters and accessories Manufacturer:Cisco Form Factor:external Product Line:Cisco Aironet Model:Power Injector

Brand : Cisco Systems, Inc. Series : 350 Model : SF350-48MP-K9-NA Format : Desktop Network Management Type : Ethernet Switch Uplink Ports : Yes Uplink Interface : SFP Primary Ports : 48 x Fast Ethernet Network Fast Ethernet Gigabit Ethernet 4 x Gigabit Ethernet Expansion Slot 2 x Gigabit Ethernet Network Primary Port Speed : 10/100Base-TX 1000Base-X 10/100/1000Base-TX Data Transmission Uplink Speed : SFP Weight : 16.2 Model : SF350-48MP

Device Type    : Switch - 48 ports - L3 - ManagedEnclosure Type     :Rack-mountable 1USubtype    :25 Gigabit Ethernet / 32Gb Fibre ChannelPorts    :48 x 1/10/25 Gigabit Ethernet / 8/16/32Gb Fiber Channel / FCoE SFP+ + 6 x 40/100 Gigabit QSFP28 / FCoEPerformance    :Bandwidth: 3.6 TbpsActive SPAN sessions: 4Capacity:     Multiple Spanning Tree Protocol instances: 64HSRP groups: 490Per VLAN Rapid Spanning Tree instances: 4000Maximum number of links in a port channel: 32Maximum number of port channels: 512ECMP paths: 64Virtual Routing and Forwarding (VRF) instances: 16000VLANs supported: 4096ACL entries (egress): 2000IGMP snooping groups: 32000Multicast routes: 32000Latency: < 1 µsMAC Address Table Size : 512K entriesRouting Protocol    : OSPF, RIP, RIP-2, BGP, EIGRP, HSRP, PIM-SM, MSDP, ECMP, MPLSFeatures:    Spanning Tree Protocol (STP) support, Multiple Spanning Tree Protocol (MSTP) support, Access Control List (ACL) support, Virtual PortChannel (vPC) technology, MACsec support, 4 fans, Virtual Extensible LAN (VXLAN), Source-Specific Multicast (SSM), Ethernet Virtual Private Network (EVPN), 40MB system buffer, Power On Auto Provisioning (POAP)Compliant Standards :     IEEE 802.1aeRAM :    64 GBBuilt-in Devices : 128 GB SSDInterfaces    48 x 1/10/25Gbit LAN / 8/16/32Gb Fibre Channel SFP+ downlink6 x 100Gbit/40Gbit LAN QSFP28 uplink1 x management RJ-451 x USB1 x serial (RS-232)

Brand: CiscoModel No: WS-C2960G-48TC-L Cisco 2960 SwitchMinimum Order Quantity: 1 PieceArea Network Type: LAN CapableNumber of Ports: 44Switch Capacity: 2GBuffer Size: 128 KbLED Indicator: RequiredProduct Type: SwitchForm Factor External: 1U

Brand: CiscoModel No: WS-C3750G-24TS-E1UMinimum Order Quantity: 1 PieceArea Network Type: LAN CapableNumber of Ports: 24LED Indicator: RequiredForm Factor: Fixed, Rack Mountable 1U, Stackable/ClusteringProduct Type: Switch

Brand: CiscoArea Network Type: LAN CapableBuffer Size: 128 KbLED Indicator: RequiredPower Source: Electric

Brand: CiscoMinimum Order Quantity: 1 PieceLED Indicator: RequiredForm Factor: DesktopNumber of Ports: 24Product Details: WS-CE500-24TTProduct Type: Cisco Catalyst Switches

Brand: CiscoMinimum Order Quantity: 1 PieceLED Indicato: RequiredProduct Type: SwitchForm Factor Fixed: Rack Mountable, Standalone/Clustering

Brand: CiscoModel: ME 3400G-12CS ACFeatures: VLAN support, layer 2 switching, layer 3 switching, trunkingSecurity features: 12 dual-purpose (10/100/1000 and Small Form-Factor Pluggable [SFP]) portsProduct Type: Gigabit EthernetPorts: 12 x 10/100/1000 + 12 x shared SFP + 4 x SF

Brand: CiscoModel: WS-C4948-10GE-S Cisco 4948 SwitchDetail: Cisco 4948 Switch WS-C4948-10GE-SProduct Type: LAYER 3 SWITCHForm Factor: 1-RACK-UNIT (1-RU)Ports: 48

Brand: CiscoModel No: 2950 SeriesMinimum Order Quantity: 1 PiecePorts: 24Warranty: 1 year Warranty